SEARCH FOR AN MOT TEST CENTRE IN 3 EASY STEPS
FIND AN MOT TEST STATION Find



UKmot.com

Car MOT Manual 2012 onwards


1.1 Front and Rear Position Lamps

Information
This inspection applies to all vehicles, except those which either have no front or rear position lamps or have such lamps permanently disconnected, painted over or masked that are:

only used during daylight hours, and
not used at times of seriously reduced visibility.

If this situation occurs, the vehicle presenter should be issued with a VT32 advisory notice recording the above.

Obligatory front and rear position lamps are lamps required by Regulations to be fitted to a vehicle to indicate its presence and width when viewed from the front or rear.

Two front position lamps must be fitted, one on each side and show a steady white light to the front or yellow if incorporated in a yellow headlamp.

Two rear position lamps must also be fitted, one on each side, showing a steady red light to the rear.
Note: A bus first used before 1 April 1955 requires only one rear position lamp on the centre-line or offside of the vehicle.

Dim-dip headlamp systems require the front position lamps to be checked for operation with the ignition switched off. This may involve the operation of a separate switch.

Additional or optional lamps are not included in the inspection.

Tricycle and quadricycle requirements are detailed at Section 9.1.
Method of Inspection
A. Front and Rear Position Lamps

1. Check the presence and security of the switch.
2. Check that the front and rear position lamps
illuminate with a single operation of the switch. 3. Check that the lamps:
a. are correctly positioned and secure

Note: The precise position of obligatory lamps is not part of the inspection, but check visually that the lamps are at about the same height and the same distance from each side of the vehicle.
b. are working
c. are not obscured
d. are in good condition

Note: An effective proprietary repair e.g. lens repair tape etc. must be assessed on its merits, considering security, colour, light output and durability.
e. show light of the correct colour

Note: Some front position lamps have a blue tinge to the light. This is acceptable provided the light is predominantly white.
f. are not adversely affected by the operation of any other lamp.
Reason for Rejection
1. A switch missing, insecure or not able to be operated from the normal driving position.

2. The front and rear position lamps do not illuminate with a single operation of the switch.

3. An obligatory lamp:
a. missing, insecure, obviously incorrectly positioned or does not face to the front or rear as appropriate
b. inoperative or less than 50% of the light sources illuminating
c. obscured so that less than 50% of the lamp illuminating surface is visible from the front or rear as appropriate
d. not visible from a reasonable distance due to excessive damage, deterioration, or having products on the lens or light source
e. shows a light other than red to the rear and white to the front or Yellow if a front position lamp is incorporated in a yellow headlamp
f. adversely affected by the operation of any other lamp, e.g. dual-function lamps on foreign vehicles.

1.1 End outline marker lamps Class 5 only

Information
This inspection only applies to Class 5 vehicles fitted with front and rear position lamps.

End outline marker lamps are required on vehicles:

exceeding 2.1 metres 2100mm in width, and
first used on or after 1 April 1991, and
are in addition to front and rear position lamps.

There must be two white lamps visible from the front positioned at windscreen upper edge level or higher and two red lamps visible from the rear, positioned as high as is practicable.

Note: The front and rear end outline marker lamps may be combined in one lamp.
Method of Inspection
B. End outline marker lamps Class 5 only
1. Turn on the position lamps and check that two front and two rear end outline marker lamps:

a. illuminate simultaneously with the position lamps
b. are securely fitted to the vehicle, one of each on each side
Note: The precise position of end outline marker lamps is not part of the inspection, but
check visually that the lamps are not obviously incorrectly positioned.

c. are working
d. are not obscured
e. are in good condition
Note: An effective proprietary repair e.g. lens repair tape etc. must be assessed on its merits, considering security, colour, light output and durability.
f. show light of the correct colour
g. are not adversely affected by the operation of any other lamp.
Reason for Rejection
1. An obligatory end outline marker lamp:

a. does not illuminate simultaneously with the position lamps
b. missing, insecure, obviously incorrectly positioned or does not face to the front or rear as appropriate

c. inoperative or less than 50% of the light sources illuminating

d. obscured so that less than 50% of the lamp illuminating surface is visible from the front or rear as appropriate

e. not visible from a reasonable distance due to excessive damage, deterioration, or having products on the lens or light source

f. shows a light other than red to the rear and white to the front

g. adversely affected by the operation of any other lamp.

1.1 Registration Plate Lamps

Information
This inspection applies to all vehicles fitted with front and rear position lamps.

Registration plate lamps are required to illuminate the rear registration plate. Some vehicles may have these lamps fitted behind the number plate.

Where more than one rear registration plate lamp is fitted, any one inoperative lamp is a Reason for Rejection.

Tricycle and quadricycle requirements are detailed at Section 9.1.
Method of Inspection
C. Registration Plate Lamps
1. Turn on the position lamps and check that registration plate lamps:

a. illuminate simultaneously with the position lamps
b. are fitted
c. are secure
d. are working
e. are correctly positioned
f. does not show white light to the rear.
Reason for Rejection
1. A rear registration plate lamp:

a. does not illuminate simultaneously with the position lamps
b. not fitted
c. insecure
d. with any lamp not working
e. not illuminating the rear registration plate
f. shows white light directly to the rear.



Reproduced from the MOT Inspection Manual by kind permission of THE VEHICLE INSPECTORATE.
This website uses cookies to ensure you get the best experience on our website More info


Got it!



MOT Test | Cookie Policy | Terms/Conditions | Copyright 2000 - 2017 UKMOT.com. All rights reserved